Bose RoomMatch DeltaQ array loudspeakers are designed for permanent installation in the finest performing arts centers, auditoriums, sports arenas, dance clubs and houses of worship, in which the large-format waveguides with choice of 42 coverage patterns can provide best-in-class coverage control, sound quality and vocal clarity even in venues with difficult acoustics.
DeltaQ technology advances line-array loudspeaker design by allowing different “Q” (directivity) for each module in the array to improve sound quality by better matching array coverage to audience areas and distance, with improved phase coherency
42 large-format waveguide patterns – allows designers to customize array coverage to exact venue dimensions to minimize wall reflections and deliver best-in-class sound quality even in venues with difficult acoustics
Continuous-Arc Diffraction-Slot (CADS) Manifold – provides smooth high-frequency array summation and allows choice of 5 vertical-coverage patterns. Select number of array modules based on sound level, low-frequency pattern control and budget requirements, independent of total array vertical coverage
Bose EMB2 compression drivers – deliver the vocal power normally associated with 3-way systems with frequencies from 500 Hz to 16 kHz projected from the large-format waveguides for remarkably consistent coverage and vocal clarity
Integrated Rigging – allows fast installation of arrays with up to 8 full-range modules at 10:1 safety factor
Available RMS215 or RMS218 subwoofers – extend full-range performance to 40 Hz or 25 Hz, in flown or ground stack arrays
Available Bose PowerMatch amplifiers – configurable to provide optimal power for all RoomMatch modules and subwoofers; includes integrated loudspeaker DSP functions with optional Dante® digital audio network interface
- Houses of worship
- Performing arts venues
Oslo Concert Hall
World Revival Church
RoomMatch used by Ahmad Jamal and Yukon Kornelius
Telus Spark Science Center
Hear the Reviews
RoomMatch & PowerMatch
Frequency Response (-3 dB)
60 Hz - 16 kHz
Frequency Range (-10 dB)
55 Hz - 16 kHz
Nominal Coverage Pattern (H x V)
RM286040 and RM602840: 28°+60° x 40° or 60°+28° x 40°
RM356040 and RM603540: 35°+60° x 40° or 60°+35° x 40°
Long-Term Power Handling
Low Frequency: 500 W (2000 W peak)
High Frequency: 150 W (600 W peak)
Low Frequency: 4 Ω
High Frequency: 8 Ω
Sensitivity (SPL / 1 W @ 1 m)
LF No EQ: 94 dB
LF With EQ: 93 dB
HF No EQ: 107 dB - 108 dB*
HF With EQ: 100 dB – 103 dB*
Maximum SPL @ 1 m
LF No EQ: 121 dB
LF With EQ: 120 dB
HF No EQ: 129 dB
HF With EQ: 122 dB
Calculated Maximum SPL @ 1 m, peak
LF No EQ: 127 dB
LF With EQ: 126 dB
HF No EQ: 135 dB
HF With EQ: 128 dB
*Varies by coverage pattern
What is the primary advantage of RoomMatch asymmetrical array module loudspeakers?
For many room shapes, asymmetrical coverage patterns improve sound quality by reducing side-wall reflections, without the need to “yaw in” array aiming. Additionally, asymmetrical coverage patterns provide enhanced stereo soundstage when used in left/right pairs, or true left/center/right systems, for many venue shapes.
What are the available coverage patterns for full-range array modules?
RoomMatch array module loudspeakers are available in 42 coverage patterns , 20 symmetrical and 22 asymmetrical patterns, with many different horizontal and vertical coverage angle combinations available.
Why is it important to match loudspeaker coverage patterns with room dimensions?
With the Progressive Directivity Array configuration, both the horizontal and vertical coverage patterns are selected for each module in the array. Array coverage can be customized to exact room dimensions. This improves overall sound quality by reducing the unwanted room acoustic reflections that can cause frequency response dips and variations. In Progressive Directivity Arrays, narrow patterns are selected to cover the rear of the room, with progressively wider patterns selected to cover the middle and front seats in the room. The differences in module directivity index (DI) help equalize levels from the front seats to the rear seats. With Progressive Directivity Arrays, virtually any room size or shape can have great sound in every seat.
What is a Progressive Directivity Array?
A Progressive Directivity Array is an array where both horizontal and vertical coverage patterns of each module in array can be selected to provide optimal coverage customized to room dimensions, acoustics and SPL requirements. Overall sound quality is improved seat to seat, by reducing unwanted room acoustic reflections that can cause frequency response dips and variations. With 5 different vertical angles of coverage, the number of modules can be reduced for modest SPL and budget requirements, without sacrificing total vertical coverage angle or sound quality.
Are RoomMatch modules rated for outdoor installations?
No. RoomMatch modules have not been tested or rated for outdoor installations.
Can RoomMatch modules be used for portable tour sound applications?
No. RoomMatch array module loudspeakers have not been tested or rated for tour sound applications, in which daily setup and tear down are required, along with frequent long-haul transportation. With the ground stack accessories, occasional movement of the modules from storage to stage areas is acceptable.
Can I mix RoomMatch RMS215 and RMS218 subwoofer modules with full-range modules in the same array?
Yes. The subwoofer modules may be suspended using the optional RMSFLY215 or RMSFLY218 side-plate kit. The RMAFLG and RMAFSM accessory array frames accommodate both subwoofer and full-range modules.
Should I use RoomMatch RMS215 or RMS218 subwoofers in a three-way RoomMatch system?
Either subwoofer can be used in a three-way system. Since the maximum SPL is the same in their respective bandwidths, the decision of which to use will depend upon the needed frequency response, with the RMS215 usable down to 40 Hz (-10 dB) and the RMS218 usable down to 25 Hz (-10 dB).
What is the recommended power amplifier and signal processor for RoomMatch modules?
RoomMatch array modules provide optimal performance when used with Bose PowerMatch configurable power amplifiers. However, RoomMatch modules may be powered by any professional amplifier that meets the recommended power requirements. RoomMatch loudspeakers connect and configure easily to PowerMatch PM8500 and PowerMatch PM4500 amplifiers. Built-in loudspeaker and array EQ pre-sets, limiting, time delay, special array compensation filters and suitable output power ratings make these amplifiers ideal for use in designs with RoomMatch array module loudspeakers. Additionally, the Bose ControlSpace engineered sound processor also contains presets for required loudspeaker signal processing of RoomMatch modules, and can be used with power amplifiers from any manufacturer. Generic EQ, limiting and delay recommended settings are available for manual setup of other brands of DSP and amplifiers and may be downloaded from pro.Bose.com.
Most 2-inch diaphragm compression drivers use crossover points of 1500 Hz or higher. How can the EMB2 compression driver use a 550 Hz crossover point without severely limiting power handling?
The EMB2 extended mid-band compression driver is designed specifically for RoomMatch loudspeakers. A new, patented phase plug allows response down to 300 Hz from a small-diaphragm driver, while lowering total harmonic distortion by reducing the compression ratio. With six EMB2 drivers in each full-range module, the combined diaphragm area is 50% greater than that of a 4-inch diaphragm driver, for improved midband response from 500 to 1000 Hz.
What is the maximum number of modules that can be used with standard rigging hardware?
Up to eight (8) modules with a 10:1 safety factor.
What is the best method to determine array room coverage and aiming?
Bose Modeler sound system software (version 6.7 or higher), which simulates the actual room acoustics, contains a new Array Design Tool to help system designers determine the optimal configuration and placement of RoomMatch arrays in a model.
Can I suspend the RoomMatch array frames from the center rail?
Yes. Due to recent modifications we have made to the array frame to increase its working load limit to the same rated limit as the other rails, you can now do permanent installations from the center rail as well.
Can single modules be suspended overhead without using an array frame?
Yes. Always use an accessory array frame or bracket to suspend RoomMatch full-range modules. However, the RMS215 and RMS218 subwoofer modules includes integrated M10 threaded inserts to allow suspension without array frames, provided the published Working Load Limits of the inserts are not exceeded.
Can the RMPULL pull-back bracket or RMBRKT surface-mount brackets be used with the RMS215 or RMS218 subwoofer module?
No. The configuration of the threaded inserts and RMSFLY plates does not allow the RMS215 or RMS218 subwoofer module to be suspended using the RMPULL pull-back or RMBRKT surface-mount brackets.
Can RoomMatch modules be used for ground stack applications?
Yes. Optional ground stack accessories are available to allow up to three (3) RoomMatch modules to be used for side and stage fill applications that require occasional movement. The ground stack accessories require at least one RMS215 or RMS218 subwoofer module be used in the ground stack array.